Litter-Robot 3: Getting Started (US)

Visit our Getting Started page for setup directions, manuals, and video tutorials.

What's in the box

Pre-check

Remove cardboard and tape

Remove the cardboard spacers between the bonnet and globe, and between the waste drawer and base. Remove the tape from around the entryway.

Check bonnet tabs

Confirm that the side and rear bonnet tabs on both sides of the unit are secured in their corresponding slots.

Secure the key

Confirm that the key on the rear of the unit is located in the pocket.

Ensure proper placement

Your Litter-Robot comes fully assembled and ready to use. Get started by following the steps below.

1. If possible, place Litter-Robot in the same location as the old litter box (at least during transition).
2. Make sure the unit is on a firm, level surface in a cool, dry location.
3. Locate the unit near a power outlet. Ensure the unit isn’t pushed against a wall or into a corner (must not be touching any walls).
4. Place litter mats or rugs in front of the unit.

Add litter

Add clumping litter

Litter-Robot’s litter sifting system requires clumping litter. Litter beads and crystals that are small enough to pass through the screen will also work.

DO NOT use litters that are strictly absorbent, non-clumping, loose-clumping, newspaper-based, or wood-based pellets.

Don’t overfill the globe: Fill the globe through the opening until litter meets the raised fill line when spread flat (about 8-10 lbs by weight or 1 gal by volume). 

Plug it in

Plug the small end of the power supply into the socket on the back of the base. Then plug the AC/DC adapter into a wall outlet.

Initial clean cycle

Locate and press the Power button. Litter-Robot will perform an initial clean cycle that will last about 2 ½ minutes.

Litter-Robot 3 Connect: Download the Whisker App

Download the Whisker app and follow the onboarding instructions.

Introducing your cat to Litter-Robot

Most likely, your cat will quickly adapt to Litter-Robot. When using in automatic mode, be sure your cat or kitten weighs at least 5 lbs—the weight scale will not recognize cats weighing less than 5 lbs.

Learn more about introducing your cat to Litter-Robot here.

Empty the waste drawer when indicated by the app or the flashing blue light on the control panel. How often you empty the waste drawer depends on the number and size of your cats. 

For two average-sized cats, twice per week is typical. For a single cat, once per week is usually sufficient.

To empty the waste drawer, simply pull out the waste drawer using the handle, and gather the edges of the liner bag and dispose.

To install a new liner or trash bag, just roll down the edges of the liner a few times and push the rolled edge of the bag into each of the four tabs.

Always press the Reset button after emptying the waste drawer.

If you use the Whisker app, press Reset Gauge in the Controls section of the app when you empty the waste drawer to reset the waste drawer level in the app.

How often you add litter depends on how many cats use Litter-Robot and how frequently they use it. Litter-Robot uses litter very efficiently since the patented sifting mechanism only removes the clumps. We recommend checking the litter level each time you empty the waste drawer. If the litter is below the raised fill line inside the globe, add just enough litter to meet the line. Always press the Reset button after adding litter.

Control panel buttons

Power

• Press and release the Power button to turn the robot ON or OFF. The robot will begin a clean cycle when power is turned on.
• Press and hold, while at the home position, to enter night light setting mode.

Cycle

• Press and release the Cycle button to start a clean cycle.
• Press and hold, while at the home position, to enter sleep mode.

Empty

• Press and release the Empty button to start an empty cycle (empties all litter into the waste drawer).
• Press and hold, while at the home position, to enter cycle delay setting mode.

Reset

• Press and release the Reset button to reset the cat sensor. (Do this after emptying the waste drawer, adding litter, etc.)
• Press and hold, while at the home position, to enter control panel lockout.

Indicator lights

• Solid blue: Robot ready and connected
• Flashing blue: Waste drawer full
• Solid blue and yellow: Sleep mode enabled, within specified sleep time
• Solid yellow: Robot cycling
• Slow flashing yellow: Cycle interrupted or bonnet removed; check for excess litter or check bonnet
• Quick flashing yellow: Potential pinch condition detected; check for blockage and press any button
• Solid red: Cat detected and cycle delay countdown initiated. No action required or press Reset to cancel timing.
• Flashing red: Cat sensor fault. Check for excess weight (such as too much waste or litter) and press Reset.

Installing Accessories

Litter-Robot 3 Ramp Installation

Litter-Robot 3 Fence Installation

Litter-Robot 3 Carbon Filter Installation

Looking for our Litter-Robot 4 Getting Started Guide? Click here

Need Technical Support?
Our Troubleshooting Wizard will solve most issues and is the fastest way to get help.

Troubleshooting Wizard